Quail brooder setup, week by week

Start Coturnix chicks at 90–95°F and lower the heat about 5°F each week. By about week 5, chicks can hold their own body temperature in a room near 70°F. The most common mistake is overheating them, not chilling them.

Updated November 18, 2026 · Just a Yolk

The numbers

  • Week 1: 90–95°F. Texas A&M says 95–97°F.
  • Space: 6 chicks/sq ft for weeks 0–2, 4/sq ft for weeks 2–6, and 3/sq ft after that.
  • Feed: game bird starter at 24–30% protein, ground fine in week 1. Never layer feed.
  • Water: put pebbles or marbles in the waterer for the first 1–2 weeks so chicks can't drown.

Brooder temperature by week

AgeTemperature at chick level
Days 1–790–95°F (32–35°C)
Days 8–1485–90°F (29–32°C)
Days 15–2180–85°F (27–29°C)
Days 22–2875–80°F (24–27°C)
Days 29–3570–75°F (21–24°C)
After about week 5No extra heat if the room stays near 70°F and the chicks are fully feathered

This schedule is from Mississippi State. Watch the chicks more than the thermometer. Chicks crowded under the heat are cold. Chicks pressed against the far walls, panting, are too hot. Chicks spread evenly and peeping quietly are just right.

Space, bedding and waterers

AgeChicks per sq ftExample: 2 × 3 ft brooder (6 sq ft)
Weeks 0–26Up to 36 chicks
Weeks 2–64Up to 24 chicks
After week 63Up to 18 birds

Feed

Texas A&M recommends a 26–30% protein game bird starter for the first 6 weeks, ground to the texture of cornmeal in week 1, then a 20% grower. UC ANR gives 24–28% (game bird or turkey starter). Never feed layer ration to chicks. It contains too much calcium for them.

DIY brooder plan (2 × 3 ft)

A simple plywood box with a hardware-cloth lid that holds up to 36 chicks for the first two weeks. It needs only basic tools.

Heat lamp clamped over the lid (warm end) Waterer at the cool end 36 in 18 in 24 in deep Hinged lid: 1/4 in hardware cloth on a 1×2 frame

Cut list

PartQtySizeMaterial
Floor136 × 24 in1/2 in plywood
Long sides236 × 18 in1/2 in plywood
Short sides223 × 18 in1/2 in plywood
Lid frame, long236 in1×2 board
Lid frame, short222½ in1×2 board
Lid mesh136 × 24 in1/4 in hardware cloth
Hardware—2 hinges, 1 hook latch, 1¼ in screws, staples—
  1. Screw the sides to the floor, with the short sides fitting between the long sides.
  2. Build the 1×2 lid frame and staple the hardware cloth to it, folding the cut edges under.
  3. Hinge the lid to one long side and add a latch on the other side.
  4. Clamp the heat lamp over one end so the other end stays cooler, giving chicks a choice of temperatures.
  5. Add 2–4 in of shavings and run the heat for a day before the chicks arrive.

We chose 1/4 in mesh for the lid because UC ANR says chick enclosures need hardware cloth finer than 1/2 in. Keep the heat lamp firmly secured, away from bedding, and use a guard. Heat lamps are a common cause of barn fires.

Sources

  • Mississippi State University Extension, "Quail Brooding Temperatures." extension.msstate.edu
  • Texas A&M AgriLife Extension L-5215, Producing Quail for Home Consumption: space, bedding, waterers, feed, vitamins. tamu.edu
  • University of California ANR Publication 8155, Raising Game Birds: starter protein, layer feed warning, mesh size. ucanr.edu
  • Jacob J, McCrea B. "Raising Japanese Quail in Small and Backyard Flocks." poultry.extension.org

More quail guides